NUC8i7BEH

[GUIDE] Building a Mac mini beast with NUC8i7BEH

Overview

This guide derives from @Rehabman’s [Guide] Booting the OS X installer on LAPTOPS and [Guide] Intel NUC7NUC8 using Clover UEFI (NUC7i7Bxx,NUC8i7Bxx,etc) but the procedure has been simplified in order to provide a quick guide to install Mojave on the NUC8i7BEH.

NUC8i7BEH

Performance

NUC8i7BEH

NUC8i7BEH

NUC8i7BEH

NUC8i7BEH

Specs

  • HyperX Impact DDR4 SODIMM 16GB * 1 (Recommend two sticks in dual-channel, 16GB of RAM works fine so far for me) Crucial DDR4 SODIMM 16GB I bought was not compatible with my NUC8. For more information about the recommended RAMs by Intel, see Memory Modules
  • Crucial MX500 1000G SATAIII SSD (I need the M.2 slot for Wi-FI/Bluetooth.)
  • Wi-Fi/Bluetooth Card
    • BCM943602CDP (4 antenna, IPEX1 connector) Wi-Fi/Bluetooth + M.2 NGFF Key B+M AdapterIntel antenna replacement is required.
    • BCM94360CS2 (2 antenna IPEX4 connector) Wi-Fi/Bluetooth + M.2 NGFF Key B+M AdapterIntel antenna replacement is NOT required but 2.4 GHz will have conflicts with bluetooth as they share the same connector.
  • M.2 NGFF Key B+M Adapter
  • LT Link Dual Thunderbolt 3 eGPU Dock
  • Sapphire RX 460 4G (firmware upgraded to RX 560)
  • Mojave 10.14.2 Final Cut Pro has better performance on 10.14.2, less exporting time and better stability than the performance on 10.14.3.

Works

  • AirDrop, Handoff (Apple Wi-Fi/Bluetooth required)
  • iMessage (complete serial required)
  • All USB3.1 Gen1/USB2.0 ports
  • USB3.1 Type-c Hotplugging
  • Hardware Acceleration (Final Cut Pro X, VideoProc, Compressor tested.)
  • Thunderbolt 3 eGPU (Final Cut Pro X, VideoProc, Compressor tested.)

Not working

  • Thunderbolt 3 eGPU Hotplugging

Preparation

BIOS settings

  • BIOS version 0056 (Please do not use the latest one, 0064. If so, please downgrade to 0056, I have attached the firmware in the respository since it was no longer provided from Intel support.)

BIOS setup can be accessed by mashing the F2 key while booting up. It will get you to the main BIOS setup screens. To start, choose “Load Defaults” (choose from the menu or press F9 in the BIOS setup).

Then change:

  • Boot -> Boot Configuration, disable “Network Boot
  • Power -> Secondary Power Settings, “Wake on LAN from S4/S5“, set to “Stay Off
  • Boot -> Secure Boot, disable “Secure Boot
  • Devices -> OnBoard Devices, disable “Bluetooth” (macOS is not compatible well with Intel Wi-Fi/Bluetooth)

Suggested:

  • Boot -> Boot Priority -> Legacy Boot Priority, enable “Legacy Boot“.

Installation

Option 1: GUI (recommended)

Option 2: Command-line

Note: If you get an error that says “This copy of the Install macOS Mojave.app application is damaged, and can’t be used to install macOS”, then open up a terminal and set the date to March 3rd, 2019 at 00:00 with date 030300002019

Post-installation

Clover EFI

  • Download the latest EFI Clover (see release)
  • Mount EFI folder with EFI Mounter V3 or Clover Configurator
  • Place the downloaded EFI folder in your local EFI drive

Fixing Continuity

Wi-Fi/Bluetooth Adapter

NUC8i7BEH

  • 2-pin JST 1.00mm (pitch) connected to the adapter
  • 4-pin JST 1.25mm (pitch) connected to the NUC internal USB2.0 connector (see “G” “H”)
Scheme

NUC8i7BEH

IPEX1 Antennas

The original antennas on NUC are using IPEX4 connector while the BCM943602CDP is using IPEX1. Thus, I completely removed the original ones and replaced them with four IPEX1. However, it’s worth mentioning that the quality of the signal drops after the replacement (for both Wi-Fi and Bluetooth).

NUC8i7BEH

Continuity Activation Tool (C.A.T)

To enable conitinuity, you must have an invaild serial number (meaning never been used by other Macs), for detailed information, please check Generating invaild serial number from hackintosher. If everything is ready and yet you still cannot have AirDrop and Handoff, please try C.A.T to activate continuity.

FRC Reverse Proxy

Frp is a fast reverse proxy to help you expose a local server behind a NAT or firewall to the internet. As of now, it supports TCP & UDP, as well as http and https protocols, where requests can be forwarded to internal services by domain name. For example, with Frp, VNC port (5900), SSH port (22), and FTP port (445) on Macs behind a NAT, can be exposed to the public. Therefore, a user can have access to Screen SharingFile Sharing remotely.

Credit

黑苹果EFI大全,免费分享黑苹果EFI大全,收集于开源渠道分享,如果有分享,请来信到maceficom@163.com,我们会添加到黑苹果EFI大全中。